Juniper Simulator Labs

The labs made available in the Juniper Simulator are given below. The labs are intended to provide some hands-on practice to beginners. It is encouraged that you write your own labs and practice after going through the labs provided here. Please note that we add and/modify the labs from time to time.

Labs

• Router Fundamental Labs:

  • Entering configuration mode on a router and exit

  • Setting Host Name

  • Setting Routers domain Name

  • Configuring Root Password

  • Configuring DNS Name Server

  • Configuring Backup Router

  • Router Interface address Configuration

  • Shut down an Interface

  • Set Interface Description

  • Configuring the Encapsulation on a Physical Interface

  • Configuring Keepalives

  • Set Keepalive Timers

  • Configuring the management Ethernet interface (fxpo)

  • Setting Bandwidth on an interface

  • Setting the hold-time value on a physical interface 

  • Configuring the DTE Clock Rate

  • Basic gigabit ethernet configuration on a J-series router

  • Configuring speed on sonet interface

  • Show chassis commands on J and M series routers

• Static Routing Labs

  • Configuring static routes

  • Ping test

  • Telnet

  • Traceroute

  • Connectivity check between Router and workstations

  • Pinging between two workstations

  • Pinging between two workstations on different subnet

  • Tracing route from workstation to router

• Policies Configuration Labs

  • Routing Policy Lab 1

  • Routing Policy Lab 2

• RIP Configuration Labs

  • RIP Configuration

• Dynamic Routing Labs

  • Ping test by configuring RIP

  • Ping test by configuring OSPF with multiple areas

• Show command labs

  • Show commands lab1

• OSPF Labs

  • OSPF Configuration

  • OSPF Configuration and Verification

• BGP Labs

  • BGP Configuration

• MPLS Labs

  • Enabling MPLS family on the interface

  • Enabling MPLS protocol on the interface

  • Enabling LDP protocol on the interface

  • MPLS show commands

  • MPLS ping and traceroute

  • Configuring MPLS using OSPF

• IPV6 Labs

  • Configuring IPv6 address on a interface in EUI-format

  • Configuring IPv6 address on a interface in general form

  • Ipv6 show commands

  • Configuring IPV6 static routes

  • Ping Test using IPV6

  • Traceroute on IPV6

• Firewall Filter (ACL) Labs

  • Creating a Firewall filter

  • Applying firewall filter to an interface

  • View Firewall filter entries

  • Configuring and Verifying firewall filter Lab Scenario-1

  • Configuring and Verifying firewall filter Lab Scenario-2

• Network Address Translation Labs

  • Configuring Source NAT using Egress interface Address

  • Configuring Source NAT Translation pool

  • Configuring Destination NAT pools

  • Creating Destination NAT rule set

  • Configuring Static NAT for single address translation

  • Configuring Source NAT using multiple rules Lab Scenario-1

  • Configuring Source NAT using multiple rules Lab Scenario-2

  • Configuring Destination NAT using multiple rules

• Exercises on DHCP

  • Configuring juniper router as a DHCP Server

  • DHCP client configuration

  • Configuring two DHCP clients and DHCP verification commands

  • Assigning ip address to PC(computer) from DHCP server

• Exercises on VPN

  • Configuring Address Books and Address Sets

  • Configuring a security zone and bind the interfaces to the appropriate

  • Configuring host-inbound services for each interface in the zone

  • Configuring IKE Phase 1 Proposal

  • Configuring IKE Phase 1 Policy

  • Configuring IKE Phase 1 gateway and reference the IKE policy

  • Configuring IPSEC Phase 2 proposals

  • Configuring IPSEC Phase 2 policies and reference the IPSEC proposals

  • Configuring the IPSEC Phase 2 VPN tunnel and reference the IPSEC Phase 2 policy

  • Configuring Security Policies

  • Configuring and Verifying Policy based VPN

  • Configuring and Verifying Route based VPN

• Basic Switch Labs

  • Entering configuration mode on a switch and exit

  • Setting Hostname

  • Set interface description

  • Shutdown an interface

  • Basic CLI commands

  • Configure bandwidth on an interface

  • Configuring ether-options on the gigabit ethernet switch

  • Configuring the management IP address on EX series switch

• VLAN labs

  • Configure a port for membership in that VLAN

  • Configuring an interface as a trunk port

  • Configuring VLANs on EX series switch

  • Configuring Routed VLAN interface (Inter-VLAN routing) on a switch

  • Creating DHCP pool on EX series switches 

  • Configure DHCP Server for multiple vlans in EX series switches

  • Vlan Scenario

  • Troubleshooting Lab with trunk functionality

  • Routing between vlans and ping test

• Spanning Tree Protocol and VSTP labs

  • Configuring STP Timers

  • Setting bridge priority on switch

  • Configuring port priority

  • Verifying STP

  • Enabling VSTP on all VLANs

  • Enabling VSTP on a VLAN using a single VLAN-ID / VLAN-Name

• PoE labs

  • Configuring guard-band and maximum power on PoE enabled interface

  • Configuring power management mode on PoE enabled interface

  • Disabling a PoE interface

  • Setting power priority on all PoE enabled interfaces

* - New lab exercises added in latest version 4.6.0 updated on 11/10/2021

Any suggestions or feedback, please email: simulator@certexams.com

Updated on 1 Aug, 2022