Cert-Ex™ Network Simulator w/ Designer for CCENT : Network Simulator Labs

The router labs made available in the CCENT Network Simulator are given below. The labs are intended to provide some hands-on practice to beginners. It is encouraged that you write your own labs and practice after going through the labs provided here. Please note that we add and/modify the labs from time to time.

Labs

• Basic Exercises

  • Logging to the router

  • Introduction to Basic User Interface

  • Basic Show commands

• Routing IOS Fundamental Labs

  • Banner MOTD : Setting Message of the Day

  • Setting host name

  • Interface configuration

  • Setting bandwidth on an interface

  • Setting console password

  • Setting telnet password

  • Setting auxiliary password to router

  • Implementing exec-timeout command

  • Copy Running Configuration to Startup Configuration

  • Router CDP configuration

  • Show CDP configuration

  • Show CDP neighbors

  • Bringing up a Router interface

  • Set keepalive timers

  • Setting Hostname and MOTD Banner

  • Configuring Router Console and Line Passwords

  • Viewing Host Table Entries

  • Viewing ARP Entries

  • Telneting between Routers

  • Configuring workstation as TFTP server

• Exercises on Routing Fundamentals

  • Introduction to IP

  • Configuring static routes

  • Implementing and Verifying Static Routes

  • Configuring default routes

  • Implementing and Verifying Default Routes

  • Configuring Loopback Interface

  • Connectivity Tests with Traceroute

  • Configuring RIP routing protocol

• Exercises on RIP Routing Scenarios

  • RIP Routing Configuration-Scenario

  • Viewing IP RIP Information

  • Configuring RIPv2

  • RIP2 Routing Configuration

• Exercises on OSPF

  • OSPF Configuration in single area

  • OSPF troubleshooting lab scenario-1

  • OSPF troubleshooting lab scenario-2

  • OSPF troubleshooting lab scenario-3

• Exercises on Access-Lists

  • Creating an access-list

  • Applying access-list to an interface

  • View access-list entries

  • Standard access-lists: Scenario lab 1

  • Standard access-lists: Scenario lab 2

  • Router Access-List Configuration

  • Configuring and Verifying Standard Access List

  • Configuring and Verifying Extended Access List

  • Configuring and Implementing Extended Access List

  • Verifying Extended Access List

  • Named Access List

• Exercises on Network Address Translation

  • NAT scenario-1

  • NAT scenario-2

  • NAT scenario-3

  • Dynamic NAT scenario-1

  • NAT troubleshooting scenario-1

  • NAT and PAT

• Exercises on DHCP

  • Configuring cisco router as a DHCP server

  • DHCP client configuration

  • Configuring two DHCP clients and DHCP verification commands

• Exercises on PPP

  • PPP configuration

• Exercises on IPv6

  • Enabling ipv6 on a cisco router

  • Enabling ipv6 on a cisco router interface

  • Configuring ipv6 on a cisco router interface with a IPv6 address in EUI-format

  • Configuring ipv6 on a cisco router interface with a IPv6 address in general form

  • Configuring loopback interface with IPv6 address 

  • Configuring ipv6 on two router interfaces connected directly and pinging the distant interface using console

  • Traceroute lab

• Exercises on IPv6 Routing Protocols

  • Enabling RIPng (IPv6 RIP Process) on a cisco router interface

  • Configuring EIGRPv6 on two routers and pinging between them

  • Entering RIPng router configuration mode and setting global parameters on a cisco router

  • Enabling OSPF for IPv6 on a Cisco router interface

  • Configuring OSPF on two router interfaces

  • General IPv6 configuration on 2610 series router

• Exercises on MPLS

  • Configuring a Router for MPLS Forwarding and verifying the configuration of MPLS forwarding.

  • Enabling MPLS

  • Configuring MPLS LDP

  • Configuring MPLS using EIGRP

  • Configuring MPLS using OSPF

  • Configuring MPLS using RIP

  • MPLS Show commands

• Cisco Switch IOS

  • Introduction to Switch

  • 2950 console password assignment

  • 2950 vty password assignment

  • 2950 setting privileged EXE password

  • 2950 enable interface

  • Basic interface configuration

  • Initial switch configuration

  • Catalyst 2950 switch configuration

• Switch Configuration and VLAN

  • Switch Simulator: Basic IP configuration

  • Switch Simulator: Configuring 2950 series switch

  • Switch Simulator: Troubleshooting 2950 switch

  • Network Simulator: 2950 Trunking Configuration

  • Network Simulator: Creating and Deleting 2950 VLANs

  • Network Simulator: Configuring VTP on 2950 switch 

  • Network Simulator: Configuring VTP with a VTP Client

  • Network Simulator: Troubleshooting lab with non-matching domains

  • Network Simulator: Troubleshooting lab with trunk functionality 

  • Network Simulator: Configuring devices to support VLAN

  • Network Simulator: VTP Configuration to establish client/server connection

  • Network Simulator: VLANs and Trunking between switches

  • Network Simulator: Routing between VLANs

Any suggestions or feedback, please email:

Updated on 13/03/2019

   

Cert-Ex™ Exam Simulators, Cert-Ex™ Network Simulator, Cert-Ex™ Cheatsheets are written independently by CertExams.com and not affiliated or authorized by respective certification providers. Cert-Ex™ is a trade mark of CertExams.com or entity representing Certexams.com.CCENT™ is a trademark of Cisco^® systems.